XW-1 / Hope OSCAR 68

-
Click on Image to enlarge

Despite the snow continuously falling up here on the Moor top and both Louise and I feeling full of cold, the water supply being frozen solid - BAH Humbug! I have still kept up with my usual radio antics whilst trying my best to keep us both warm and comfortable.

I have been playing around with the Radio Com software that I have had installed on my machine for the last 4 years which is proving to be unbeatable for decoding the NOOA WX SATs. This time I have been using the software to monitor the new Chinese Satellite - XW-1(HO-68). The Sat is still mainly beacon only, which transmits around 435.790MHz in CW mode. I use the Ft-847 and IO-10El antenna to receive the "bird" feeding the incoming AF from the rig to the computers sound card where the Radio Com software picks up the audio to be decoded. The software works similar to any other radio decoding software having lots of nice and useful features. The Spectrum Analyser is one of the many useful tools, in this case used to visually observe the new "birds" signal whilst decoding the received beacon's CW transmission.

The HO-68 Satellites beacon is reported to be strong world wide from the various reports from other Hams and relevant sources that I've come across on the net. As you can see from the above image I am also receiving the Hope Oscar 68(HO-68) beacon very well and I am looking forward to hearing some real activity via the new "bird" soon.
The CW TX from the HO-68 Satellites beacon was decoded by the Radio Com CW decoder which reads.

T T T T T T T T T T T T T T T T T T T T T X W X W

If you haven't yet heard the XW-1(HO-68) Satellite yet, or are new to Satellites and don't know how to track them. Have a look at downloading Satscape to help you locate them. The rest off you G L, & have a Merry Christmas.

Comments

Tomas said…
We heard it on Moday too, quite strong signal on our UV200 vertical antenna.. Max elev ~35°,that pass,so satellite was in diagram of our antenna all the time.. It was hearable to last moment and then it disappear over middle of OX..

Numbers are shortened as I found description of telemetry frames at http://www.amsat.org/amsat-new/satellites/documents/XW-1_Telemetry_Format.pdf .

73 & Merry Xmas to you all:)
1:36 pm
MØYKS Simon said…
Hi Tomas, hope you had a nice Christmas.

I hears some activity on the SSB transponder yesterday but the schedule is not so often over N.EU. I am looking forward to hearing the FM transmissions.

Have a Wonderful New Year and all the best for your blog in 2010

best 73 and many thanks for all your comments.

Simon
7:40 pm
Post a Comment

Popular posts from this blog

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl...
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr...
Read more

YAESU G - 5500 Elevation Rotator Repair

-
Image
After 10 years of careful use my G-5500 eventually developed a couple of faults on the elevation rotator side.  Fault 1. For the past year I have had to guess the elevation as the readout was no longer working on the controller unit. I suspected the position switch which was located inside the rotator up above the house roof which was a pain in the butt to say the least. Fault 2. Over the winter the gearbox on the elevation rotor seized up solid. I plucked up some courage and erected my ladder and which with the aid of a rope to lower the mast it all worked out quite straight forward. Once down out with the impact driver and away I went. Once I split the case with the impact driver which was easy, I found lots of sandy grit and dried out remains of what should have or once was gearbox/bearing grease. The next step was to inspect the seized gearbox and then remove the main shaft which can only be carried out by first removing the entire gear housing u...
Read more