Home Brew Radial Grounding stakes

-

Since I installed the Hustler 6BTV at my new QTH I have been planning on making some radials similar to the ones I have attached to my other 6BTV which is up at the Moor top QTH. The original hustler has done me proud for over six years with its ground mount and simple wire radials.

I really like the performance of these antennas as well as there durability, that's why I had to go for a second one!

I got hold of some brass sheet which I cut into strips about 40mm wide. I then cut one end of each strip into a sharp V shape. The next job was to fold the opposite end over and tap it flush to provide extra strength when hammering the stake into the ground. I then folded the complete strip into the final V shaped angle approximately 45º creating a nice brass ground stake. The finishing touch was to drill a small hole to attach a soldered lug/wire radial which can be hammered beneath the ground surface in the garden.

The second part of the job involved cutting some more brass sheet which I formed into a circular shape to be fixed at the base beneath the hustler. I drilled lots of holes in the brass grounding plate allowing me to screw many radials into it. I also formed some 8mm round bar into a U clamp which I fit to the Brass grounding plate ready to attach to the 6BTV antenna.

WX permitting I plan to have a play with my new radial kit sometime over the weekend, I have a roll of 2.5mm wire, a hammer and tape measure ready on stand by. I will try get some pictures for you to see the result. Till next time 73 have a good weekend.

Comments

Paul Blundell said…
Hi Simon,

I've been a regular reader of your blog and youtube videos for maybe 6 months now.
I have finally got my M6 licence and currently run a Yaesu FT-817 so it's QRP for me !! I've got an SRC X-80 vertical mounted only 2 feet above ground but is working quite well, I have x1 4ft copper pipe for the ground with x2 20ft wire radials dug about 1cm under ground. Does that sound pretty good to you ? I commented on this post because your idea seems like something I might try.

Anyway I'm waffling, keep up the good work on this blog and the videos coming !!!
Hope to work you on the band one day, I'll keep listening out for you !

73

Paul - M6PBB
5:36 pm
MØYKS Simon said…
Hi Paul, Congrats on your new Call sign and it sounds like your well on your way to making many QSO on the FT817 and SRC X-80.

Your radial instalation sounds alright to me, just keep adding if you can.

Look forward to hearing you on the bands soon. 73 from b Simon - 2e0hts
11:58 am
Lassia said…
Thanks for sharing with us .Surelia Industries manufactures, supplies, exports, and imports Radial drill.
11:50 am
Post a Comment

Popular posts from this blog

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl...
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr...
Read more

YAESU G - 5500 Elevation Rotator Repair

-
Image
After 10 years of careful use my G-5500 eventually developed a couple of faults on the elevation rotator side.  Fault 1. For the past year I have had to guess the elevation as the readout was no longer working on the controller unit. I suspected the position switch which was located inside the rotator up above the house roof which was a pain in the butt to say the least. Fault 2. Over the winter the gearbox on the elevation rotor seized up solid. I plucked up some courage and erected my ladder and which with the aid of a rope to lower the mast it all worked out quite straight forward. Once down out with the impact driver and away I went. Once I split the case with the impact driver which was easy, I found lots of sandy grit and dried out remains of what should have or once was gearbox/bearing grease. The next step was to inspect the seized gearbox and then remove the main shaft which can only be carried out by first removing the entire gear housing u...
Read more