EA1GHW Double Moxon Style Homebrew Satellite Antenna

-
Thanks to fellow ham and friend Edmundo - EA1GHW, I am able to show you another great home brew satellite antenna system. ED, EA1GHW from Spain has been working satellites a lot longer than myself and has had some great results with his home brew antenna systems and a couple of hand held rigs. I first saw ED in action via his YouTube video's working through AO-51 and since then we have become friends via the Internet. I keep hearing ED and ED hears me via the "birds" but unfortunately we have always had too many other stations causing lots of QRM and have yet to get each other in the log! I am sure we will get over that soon with the better weather coming and the dark nights ending.
Hear you can see ED's design on paper.

This image shows the EA1GHW satellite antenna ready to assemble.

This image shows the completed satellite dual band antenna system ready to go!

Edmundo EA1GHW mentioned that he intends to add more elements to the antenna in the near future increasing the antenna gain. He also has told me that the EA1GHW antenna is working well so far! Well done ED! thanks for sharing the images of your great antenna. Keep up the good work!
I will be listening out for ED on the future satellite passes.

Comments

Unknown said…
Nice antenna. I am disabled and unable to build the antenna. Can you help me out. Send reply to pastor.spaceboy@gmail.com

Randy
11:43 pm
Post a Comment

Popular posts from this blog

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl...
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr...
Read more

YAESU G - 5500 Elevation Rotator Repair

-
Image
After 10 years of careful use my G-5500 eventually developed a couple of faults on the elevation rotator side.  Fault 1. For the past year I have had to guess the elevation as the readout was no longer working on the controller unit. I suspected the position switch which was located inside the rotator up above the house roof which was a pain in the butt to say the least. Fault 2. Over the winter the gearbox on the elevation rotor seized up solid. I plucked up some courage and erected my ladder and which with the aid of a rope to lower the mast it all worked out quite straight forward. Once down out with the impact driver and away I went. Once I split the case with the impact driver which was easy, I found lots of sandy grit and dried out remains of what should have or once was gearbox/bearing grease. The next step was to inspect the seized gearbox and then remove the main shaft which can only be carried out by first removing the entire gear housing u...
Read more