Latest Home Brew Metal Work Project - Tripod Mount For Satellite Yagis

-
This week I continued with my latest radio project which was to be some kind of rotator mount that I could use to set up my latest Satellite array.

As mentioned in my last post, I am planning on fixing the new Satellite antenna high up on the house. However, before I can begin working on that installation I want to build everything up at ground level and give it all a good testing out, ironing out any problems there may be on the way.

With all this in mind I began to search through my scrap material pile that I have stashed away for a rainy day etc.
I soon came across some heavy duty pipe and found some screwed/threaded bar. Then with a bit of sawing, grinding and hammering, I began fabricating the scrap pipe and metal which I finished off by welding it all up into a fairly substantial tripod.

The finished tripod can easily be dismantled and folds up nice and neat allowing it to be transported without any hassle.

I finished the job by painting it black, I then fitted the Yaesu GS5500 rotator to the top of it. (as seen below in the two images).

Next, I was ready to install the two Satellite Yagi antennas.

I fitted the 435 X beam and the 145 Yagi with a short ally pole keeping the weight down to a minimum.

The video below shows the Satellite array up and running working well at ground level.


I have already made a couple of successful QSO via VO-52 as well as hearing AO-51 nice and loud last night. The new setup will be even better once I complete the full installation on the house.

Hope to hear you via the SATs soon!

Comments

PE4BAS, Bas said…
Hello Simon, that is a very nice tripod and antenna setup. Around 2000-2003 I worked a lot via UO14/AO27 and since I was not allowed HF then it was great fun. There is only one disadvantage and that is that sometimes you have to wait a long time till one of the sats is flying over. But if you really have that patience the contacts are rewarding. I think when the weather is a little better I'm going to give it a try as well. The idea of a tripod did not come up with me, for sats it's not really important to have the antennas very high. Except if they are very near to the horzizon. 73, Bas
1:05 pm
test said…
Hi Simon, Very nice setup you made here ! I'm aiming to something like this too but I could'nt deal with the price of an elevation rotor so it will have to wait. Just a question, did you try to put the antennas vertically ? I did this with my home setup with a fixed 30° elevation 3 elements yagi VHF and 5 elements UHF and vertical works best than horizontal, strange but true, HI !
Keep up the good work, 73 de Tom F8COD
6:23 pm
MØYKS Simon said…
Hi Bas, glad you like the tripod. It will be fantastic to work you sometime in the near future, I look forward to you setting up some equipment. As you know I am very active on HF in between the Satellite passes and looking after our new baby daughter. All the best Bas. Thanks for all your comments many 73.
6:48 pm
MØYKS Simon said…
Hi Tom, thanks for the advice. I changed my Yagi to vertical polarisation and am now hitting the birds much more effectively. I have noticed a massive improvement and have made lots of good QSOs on AO-51, AO-7 and VO-52 since I changed it. Hope to catch you on one of the Satellites soon Tom.
Best 73 and many tnx.
Simon
6:52 pm
Post a Comment

Popular posts from this blog

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl...
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr...
Read more

YAESU G - 5500 Elevation Rotator Repair

-
Image
After 10 years of careful use my G-5500 eventually developed a couple of faults on the elevation rotator side.  Fault 1. For the past year I have had to guess the elevation as the readout was no longer working on the controller unit. I suspected the position switch which was located inside the rotator up above the house roof which was a pain in the butt to say the least. Fault 2. Over the winter the gearbox on the elevation rotor seized up solid. I plucked up some courage and erected my ladder and which with the aid of a rope to lower the mast it all worked out quite straight forward. Once down out with the impact driver and away I went. Once I split the case with the impact driver which was easy, I found lots of sandy grit and dried out remains of what should have or once was gearbox/bearing grease. The next step was to inspect the seized gearbox and then remove the main shaft which can only be carried out by first removing the entire gear housing u...
Read more