Late Night DX - Sable Island

-

I just got lucky as I tuned around the HF bands before bed I heard a faint signal calling CQ DX. I was listening carefully on 14.160MHz SSB and realised it was VA1AXC operating from Sable Island under the call CY0/VA1AXC.


 At first CY0/VA1AXC was coming in with a 5/1 signal at my end and I did not think I would be heard, I gave my call sign an airing and woe and behold I was heard first call 5/5 in Sable Island. As we exchanged information  CY0/VA1AXC came up to a nice 5/5 signal, I was running my FT1000MP, 100W into the Cobweb. As I am posting this I am still listening to CY0/VA1AXC who has a nice pile up going on and has decided to now work split frequency. I was very lucky to have been the first station he worked whilst it was nice and quiet, some good timing and not been afraid to try my PTT paid off well as there is only 6 people on Sable Island and I just worked one of them!. 73 GN!

Comments

Unknown said…
Your comments, very similar to mine. I worked the same station late evening in May 2015. 20m was pretty quiet. Tuning casually across the band i heard a fairly weak signal. I could not believe my luck , it was CY0/VA1AXC. I called back not thinking he would hear me. To my surprise he did. There was a short qso and i was in his log. My equipment used at the time was a TS870, 100W into a Hustler 4 band vertical antenna. Looking up his qsl info was direct to his qsl manager in Japan. I sent my qsl card and received CY0/VA1AXC card within a week. Now that has to be good in any ones book. Little disappointed he was not in Lotw. Just recently March 2017 I was just doing some checks on the Lotw website,and there was the qso we had last year which counted towards my dxcc credits. Brilliant.
Reg G0OOF England
4:30 pm
MØYKS Simon said…
Excellent stuff Reg, I love catching rare stations especially when everyone else is in bed. Thanks for sharing and good to hear you gained some DXCC credits. Happy DXing my friend and best 73. De Simon M0YKS
6:57 pm
Post a Comment

Popular posts from this blog

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl...
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr...
Read more

YAESU G - 5500 Elevation Rotator Repair

-
Image
After 10 years of careful use my G-5500 eventually developed a couple of faults on the elevation rotator side.  Fault 1. For the past year I have had to guess the elevation as the readout was no longer working on the controller unit. I suspected the position switch which was located inside the rotator up above the house roof which was a pain in the butt to say the least. Fault 2. Over the winter the gearbox on the elevation rotor seized up solid. I plucked up some courage and erected my ladder and which with the aid of a rope to lower the mast it all worked out quite straight forward. Once down out with the impact driver and away I went. Once I split the case with the impact driver which was easy, I found lots of sandy grit and dried out remains of what should have or once was gearbox/bearing grease. The next step was to inspect the seized gearbox and then remove the main shaft which can only be carried out by first removing the entire gear housing u...
Read more