CQWW 2017 - Last Minute Windom Antenna Adjustments

-

My windom antenna has been in an inverted vee configuration for the last twelve months, I have carried out a few experiments with the antenna supported by the off center fed balun but have found the vee configuration far too noisy on reception.So today I managed to get the windom back to horizontal and in a straight line. I also increased the antenna height above the ground from 20 feet to around about 30 feet sloping slightly at both ends to around about 20 feet at each end.

To make life easy I got out my 30 ft telescopic pole and attached a homemade hook into the top of the pole for easy hanging.



The fiberglass pole is the quickest way for me to get a hook up high without too much trouble and with a steady hand its simple enough to extend with the antenna attached.


The neighbors probably think I am going fishing, maybe flying fish? Anyhow up she goes, where it stops no one knows!


The face of concentration as I 'hook a duck' at 30 feet, I am aiming the pole at the top of my 2 meter  antenna mast.

Achieved! On target and successfully hooked to the antenna bracket with the homemade hook and nylon rope.

 I added a telescopic mast that I sometimes use /P, this will keep the antenna up higher and in a horizontal or flat configuration. The opposite far end is supported by a tree using another homemade hook, some nylon rope and again hung with my telescopic pole to mount it up high hooked to a thick branch.


The end result looks a lot better and seems to be much better on receive, I was getting a lot of noise before but now its much more reasonable. I am referring to the 80 meter band and noise levels are fairly high no matter what .Previously with the inverted vee config, I was up at S9 + but now its horizontal I am back down to S7 and voices are much more readable again.


I tried it out on 40 meters earlier and it was equal to the vertical, I will be testing on 80 meters next as I prepare and check over the station and get excited to be almost ready for the World Wide CQ Contest this coming weekend.

Comments

PE4BAS, Bas said…
Great job Simon, nice video as well. Hope to meet you in the contest. 73, Bas
8:08 pm
MØYKS Simon said…
Tnx Bas good luck over the weekend. I'll listen out for PA6AA in the contest. Best 73 Simon
8:22 pm
Post a Comment

Popular posts from this blog

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr
Read more

New DX Contact 0n 12 Meters

-
Image
Today I managed a nice QSO with Tom ZD7X who is located at St. Helena which is quite a distance away from my location. I managed to work Tom ZD7X with a 5/9 report operating my FT-767GX with my home brew 20m delta loop assisted with the MFJ-969 to tune the antenna with 50 watts on 12 meters. 12M is rarely open and I have only had a few QSOs on this band so I guess the new Cycle has begun at last! Good DX de 2E0HTS 73
Read more