Chinese Porn!!!!!

-
Just a quick post to inform any readers regarding the abundance of Chinese comments that have been appearing here at my Ham Radio blog. They seem to be just another source of spamming in the form of porn enthusiasts rather than radio ops/ engineering fans.

Although I am quite open minded and allow all comments good or bad to be seen on my site I've decided to enable the feature that asks to Show word verification when commenting. This should filter out the Chinese Pornsters unless of course they are truly passionate about Ham Radio.

For all those interested in Chinese porn, see the previous comments. For those who like myself will get battered by there YL's for going anywhere remotely near those dubious dodgy sites, I apologise for any unsuitable links they may have attached with the seemingly harmless if not slightly puzzling comments left by my new Chinese followers?

Have a great weekend, hope to catch some of you on the bands!

Comments

Unknown said…
Those links could provide a useful source of material for the SSTV enthusiasts! :)
9:26 am
MØYKS Simon said…
lol, yes I have seen some suspicious pictures around about 14.230. definately a good idea for the more "live dangerous" type of sender. It might look good with Robot 36, Martin 1 or evan Scottie DX!
2:29 pm
Jspiker said…
Been having the same problem here with the "porn" links thrown in with comments about radio ....they must not have respect for the female gender.

BTW/ Nice bikes... I'm probably a little too old for those now but still dream of taking one last long ride in the country. For now, I'm on the mountain bike circuits. It's difficult to find level rides here in West Virginia. Lot's and lot's of mountains here.
10:30 pm
Post a Comment

Popular posts from this blog

New DX Contact 0n 12 Meters

-
Image
Today I managed a nice QSO with Tom ZD7X who is located at St. Helena which is quite a distance away from my location. I managed to work Tom ZD7X with a 5/9 report operating my FT-767GX with my home brew 20m delta loop assisted with the MFJ-969 to tune the antenna with 50 watts on 12 meters. 12M is rarely open and I have only had a few QSOs on this band so I guess the new Cycle has begun at last! Good DX de 2E0HTS 73
Read more

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr
Read more